Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Presented here below you will find some reliable details relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the task can relocate quickly; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. As opposed to working with a professional to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you might need a specialist plumber to make tube links.
This article will certainly assist you mount a new bathtub in your shower room if you have currently bought a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Planning for the Installation
First of all, the supporting framework provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, position the tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the very same for the various other faucet.
Switch on the water supply and also inspect all joints and new pipework for leakages as well as tighten them if required. Load the tub and additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has actually been used at the very least once as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break an inflexible seal, triggering the water to pass through the wall between the bath and the tiling, resulting in problems with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
As a keen reader on Installing A Bathtub, I assumed sharing that section was sensible. Make sure you take a moment to distribute this blog if you enjoyed it. Thanks a bunch for your time. Please visit our site back soon.
Give Me A Quote! Report this page